Description
Product Description
Trigger Cycle Timer Delay Controller
Trigger cycle timing
Delay switch circuit
Pulse generator
Dual MOS control
Trigger Cycle Timing Delay Switch Circuit MOS Pulse Generator DC 5V-36V Digital Tube Display
Work Mode:
P1.1:Trigger Delay Mode. Input trigger signal and then output turn ON and keep time OP. Then turn OFF after delay time OP.Keep OFF at last; The input signal is invalid if get trigger signal again during delay time OP.(Time OP can not be set 0)
P1.2:Trigger Delay Mode. Input trigger signal and then output turn ON and keep time OP. Then turn OFF after delay time OP.Keep OFF at last; Output will restart delay if get trigger signal again during delay time OP.(Time OP can not be set 0)
P1.3:Trigger Delay Mode. Input trigger signal and then output turn ON and keep time OP. Then turn OFF after delay time OP.Keep OFF at last; Output will reset and stop timing if get trigger signal again during delay time OP.(Time OP can not be set 0)
P2:Trigger Delay Mode. Input trigger signal and then output keep OFF for time OL. Then turn ON after delay time OL and then keep ON for time OP. Then turn OFF after delay time OP.Keep OFF at last.(Time OP and OL both can not be set 0)
P3.1:Trigger Delay Mode. Input trigger signal and then output turn ON and keep time OP. Then turn OFF after delay time OP and then keep OFF for time OL. Cycle the above two actions in turn.The number of cycles (LOP) can be set.Output will reset and stop timing and output OFF if get trigger signal again during loops.(Time OP and OL both can not be set 0)
P3.2:Power-ON Delay Mode. Input work power supply and then output turn ON and keep time OP. Then turn OFF after delay time OP and then keep OFF for time OL. Cycle the above two actions in turn.The number of cycles (LOP) can be set.(Time OP and OL both can not be set 0) Note:this mode no need input signal.
P4:Signal Keep Mode. Keep input signal and then output keep ON.Output turn OFF after delay time OP when the signal disappears.Reset delay time when get trigger signal again during timing.(Time OP can not be set 0)
Parameter Description:
OP: Delay time for turn On
CL: Delay time Turn OFF
LOP: Number of cycles.Range is 1-999tims.’—-’ means unlimited loop
Set Parameter:
Long press:keep press button for more than 3second
1>.Enter set parameter menu by long press button ‘SET’
2>.Work mode will flash at first when set the working mode.Short press the UP/DOWN button to select working mode P1~P4.
3>.Short press SET button to enter the system parameter settings interface.
4>.In the system parameter setting interface, short press the ‘SET’ button to switch the system parameters to be modified, short/long press the UP/DOWN button to modify value.
5>.Short press button ‘STOP’ to select timing range.
6>.Short press button SET to set next parameter.
7>.Save the parameter settings and exit the settings interface when long press ‘SET’ button after all the parameters are set.
8>.Main interface:Display 000 if no output.
9>.Set interface:Long press SET button enter into set interface.Long press SET button again into main interface after set parameter.
Buyer’s Diagram show
See the diagram attached for how to wire the high-level trigger.
You can connect the ground wire and positive wire from the trigger to the input power connection on the PEMENOL unit but that is not suggested in the documentation.
IMPORTANT NOTE – For the unit to work with the trigger used to activate and deactivate the units cycle you must select the P3.1 setting.
Package Listing
1pcs ZK-J06 Delay Controller Module
6pcs Acrylic shell
4pcs M3*12mm Copper column
4pcs M3*5+6mm Copper column
8pcs M3*6 screw
Parameters
Working Voltage:DC 5V-36V
Control Current:30A(Max and need heat sink!Normal temperature 15A 400W)
Quiescent Current:15mA
Working Current:50mA
Trigger signal source: High level trigger (3.0V~24V)
Note
Module can output voltage same to input voltage
GND and GND- can not connect together otherwise module can not work normally
Please read use manual and description before use
Buyer’s Diagram
Package Included
Size
Installation Complete
Features:
1>.Digital tube display
2>.Support high level trigger
3>.Emergency stop function
4>.Sleep mode,Wake up with any button
5>.Automatically save parameters
6>.Dual MOS control support more than 15A 400W
7>.Support reverse connection protection
8>.Continuously adjustable from 0.1 seconds to 999 minutes
9>.Optocoupler isolation to enhance anti-interference ability
Additional Features:
1>.Auto sleep function: Long press button ‘STOP’ in the normal running interface to turn on or off auto sleep function.
1.1>C-P:Turn ON auto sleep function.Screen will automatically turns off if there is no operation within five minutes.It can be wake up by any buttons.
1.2>.O-d:Turn OFF auto sleep function.
2>.Enabled/Disabled output by short press button STOP:
2.1>.ON:Enabled output during delay time OP.
2.2>.OFF:Disabled output during delay time OP.Module can not output any signal at this mode.
3>.Common ground:User can connect GND of trigger signal to GND of module by short pads GND-T and GND.But it is not recommended, which will reduce the anti-interference ability of the module.
Note:
1>.Module can output voltage same to input voltage.
2>.GND and GND- can not connect together otherwise module can not work normally.
3>.Please read use manual and description before use.
Application
For automatic watering system DIY
Used to control curtains
For pet automatic feeding equipment
For controlling lighting
Automatic water change control for aquarium
For car headlights
For automatic curtain switch
For motor automatic control operation
采集到芒果 
采集到芒果 
采集到芒果 
采集到芒果 
采集到芒果 PEMENOL Timer Delay Relay PEMENOL Timer Delay Cycle Module PEMENOL Time Delay Relay Controller Board Cycle Delay Drive Module PWM Signal Generator Driver Module Work Voltage DC 5-36V AC 85V-265V DC 6V-30V DC 3.3V-30V DC 5V-30V Timing Range 0.1s-999mins 0s-999h 0.01s-9999mins 0.000s~9999s Display Mode Dual Mos Output Dual Timing Time Auto Sleep Function PWM mode and PULSE mode Speed Regulator Driver Module
Reviews
There are no reviews yet.